NR:21-28
Vancouver, BC (July 7, 2021) Skeena Resources Limited (TSX: SKE, OTCQX: SKREF) (“Skeena” or the “Company”) is pleased to report diamond drill core results from the 2021 Phase 3 infill and exploration drilling program at the Snip gold project (“Snip” or the “Project”) located in the Golden Triangle of British Columbia. The Phase 3 program is designed to upgrade areas of existing Inferred resources from the Company’s 2020 Mineral Resource Estimate (MRE), to the Measured and Indicated categories. Reference images are presented at the end of this release as well as on the Company’s website.
Snip 2021 Phase 3 Drilling Highlights:
• 30.72 g/t Au over 3.82 m (S21-099)
• 48.44 g/t Au over 4.50 m (UG21-126)
• 33.63 g/t Au over 4.00 m (UG21-169)
• 25.64 g/t Au over 4.00 m (UG21-172)
• 58.47 g/t Au over 3.81 m (UG21-175)
• 46.94 g/t Au over 4.75 m (UG21-176)
• 110.22 g/t Au over 4.41 m (UG21-177)
True widths range from 60-100% of reported core lengths. Length weighted Au composites are constrained by geological considerations. Grade-capping of individual assays has not been applied to the Au assays informing the length-weighted Au composites. Samples below detection limit were nulled to a value of zero.
New High-Grade Mineralization Intersected in Footwall Corridor
Situated on the 412 level of the Snip underground workings, a new cluster of previously unidentified, high-grade intersections have been intercepted during the Company’s Phase 3 infill program. A total of 21 fanned underground drill holes were collared from this single drill station to recategorize Inferred resources in the deeper footwall rocks. New high-grade veining intersections were discovered by all holes only metres into the underground rock face, all of which possess above average grades and widths as highlighted by intersection 110.22 g/t Au over 4.41 m which included 730.00 g/t Au over 0.58 m (UG21-177). Other examples include 46.94 g/t Au over 4.75 m including 320.00 g/t Au over 0.50 m (UG21-176) and 58.47 g/t Au over 3.81 m including 313.00 g/t Au over 0.60 m (UG21-175). This newly drilled mineralization is open for expansion up-dip 25 m and greater than 100 m down-dip due to a lack of drill hole sampling by previous operators. The westward strike extension is open for 40 m.
2021 Phase 3 Program Description
The 2021 drilling program at Snip is designed to convert Inferred resources from the Company’s 2020 MRE to higher confidence categories (Measured and Indicated) through surface and underground drilling. Dedicated geotechnical drilling is also being completed at the Project.
About Skeena
Skeena Resources Limited is a Canadian mining exploration company focused on revitalizing the past-producing Eskay Creek gold-silver mine located in Tahltan Territory in the Golden Triangle of northwest British Columbia, Canada. The Company released a robust Preliminary Economic Assessment in late 2019 and is currently focused on infill and exploration drilling to advance Eskay Creek to full Feasibility by Q1 2022. Additionally, Skeena continues exploration programs at the past-producing Snip gold mine.
On behalf of the Board of Directors of Skeena Resources Limited,
Walter Coles Jr.
President & CEO
Contact Information
Investor Inquiries: info@skeenaresources.com
Office Phone: +1 604 684 8725
Company Website: www.skeenaresources.com
Qualified Persons
Exploration activities at the Snip Project are administered on site by the Company’s Exploration Managers, Raegan Markel, P.Geo. and John Tyler. In accordance with National Instrument 43-101 Standards of Disclosure for Mineral Projects, Paul Geddes, P.Geo. Vice President Exploration and Resource Development, is the Qualified Person for the Company and has prepared, validated and approved the technical and scientific content of this news release. The Company strictly adheres to CIM Best Practices Guidelines in conducting, documenting, and reporting the exploration activities on its projects.
Quality Assurance – Quality Control
Once received from the drill and processed, all drill core samples are sawn in half, labelled and bagged. The remaining drill core is subsequently securely stored on site. Numbered security tags are applied to lab shipments for chain of custody requirements. The Company inserts quality control (QC) samples at regular intervals in the sample stream, including blanks and reference materials with all sample shipments to monitor laboratory performance. The QAQC program was designed and approved by Lynda Bloom, P.Geo. of Analytical Solutions Ltd., and is overseen by the Company’s Qualified Person, Paul Geddes, P.Geo, Vice President Exploration and Resource Development.
Drill core samples are submitted to ALS Geochemistry’s analytical facility in North Vancouver, British Columbia for preparation and analysis. The ALS facility is accredited to the ISO/IEC 17025 standard for gold assays and all analytical methods include quality control materials at set frequencies with established data acceptance criteria. The entire sample is crushed and 1 kg is pulverized. Analysis for gold is by 50 g fire assay fusion with atomic absorption (AAS) finish with a lower limit of 0.01 ppm and upper limit of 100 ppm. Samples with gold assays greater than 100 ppm are re-analyzed using a 50 g fire assay fusion with gravimetric finish. Analysis for silver is by 50 g fire assay fusion with gravimetric finish with a lower limit of 5ppm and upper limit of 10,000 ppm. Samples with silver assays greater than 10,000 ppm are re-analyzed using a gravimetric silver concentrate method. A selected number of samples are also analyzed using a 48 multi-element geochemical package by a 4-acid digestion, followed by Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES) and Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and also for mercury using an aqua regia digest with Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES) finish. Samples with sulfur reporting greater than 10% from the multi-element analysis are re-analyzed for total sulfur by Leco furnace and infrared spectroscopy.
Cautionary note regarding forward-looking statements
Certain statements made and information contained herein may constitute “forward looking information” and “forward looking statements” within the meaning of applicable Canadian and United States securities legislation. These statements and information are based on facts currently available to the Company and there is no assurance that actual results will meet management’s expectations. Forward-looking statements and information may be identified by such terms as “anticipates”, “believes”, “targets”, “estimates”, “plans”, “expects”, “may”, “will”, “could” or “would”. Forward-looking statements and information contained herein are based on certain factors and assumptions regarding, among other things, the estimation of mineral resources and reserves, the realization of resource and reserve estimates, metal prices, taxation, the estimation, timing and amount of future exploration and development, capital and operating costs, the availability of financing, the receipt of regulatory approvals, environmental risks, title disputes and other matters. While the Company considers its assumptions to be reasonable as of the date hereof, forward-looking statements and information are not guarantees of future performance and readers should not place undue importance on such statements as actual events and results may differ materially from those described herein. The Company does not undertake to update any forward-looking statements or information except as may be required by applicable securities laws.
Neither the Toronto Stock Exchange nor the Investment Industry Regulatory Organization of Canada accepts responsibility for the adequacy or accuracy of this release.
Table 1: Snip Project Phase II 2021 Length-Weighted Drill Hole Gold Composites:
True widths range from 60-100% of reported core lengths. Length weighted Au composites are constrained by geological considerations. Grade-capping of individual assays has not been applied to the Au assays informing the length-weighted Au composites. Samples below detection limit were nulled to a value of zero. NSA – No Significant Assays.
Table 2: Mine Grid Drill Hole Locations and Orientations:
